Double Dutch Doors

#NACBDD2
Split Economy Crossbuck
Double-Dutch Door
Two Panels
4'-0" width x
4'-0" height

Recommended
Opening Measurement
4'0-1/2" width X
8'1" height

**

	Completely Assembled
	Two 4'-0" width x 4'-0" height panels *Also available in two 3'11-1/2" width x 3'11-1/2" height panels
	Twin Panels of 3/4" BC Plywood
	Bonded with glue and wood screws at back of doors.
	Wood screws installed counter sunk in critical areas for additional strength.
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all doors.
	Smooth surface panels on interiors of doors.
	Crossbuck Fascia on exterior of door unless reverse fascia requested
	Reverse Fascia available at no charge

#NACBHD1
Economy Crossbuck Lumber
Half Dutch Gate
4'-0" width x
4'-0" height

Recommended
Opening Measurement
4'0-1/2" width

**

	Completely Assembled Stall Gate with Hardware
	Old World Crossbuck "x" Design
	One 4'-0" width x 4'-0" height panel *Also available in one 3'11-1/2" width x 3'11-1/2" height panel
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all gates.
	Smooth surface inside door panel.
	All lumber secured with glue and countersunk wood screws on rear panels.

double dutch doors

#CBDD2
Split Crossbuck
Double-Dutch Door
Two Panels
4'-0" width x
4'-0" height

Recommended
Opening Measurement
4'0-1/2" width X
8'1" height

**

	Completely Assembled
	Two 4'-0" width x 4'-0" height panels *Also available in two 3'11-1/2" width x 3'11-1/2" height panels
	Twin Panels of 3/4" BC Plywood
	Bonded with glue and wood screws at back of doors.
	Wood screws installed counter sunk in critical areas for additional strength.
	All Edges surrounded with heavy gauge, "non-rusting" Mitre-Cut ALUMINUM channeling secured with wood screws.
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all doors.
	Smooth surface panels on interiors of doors.
	Crossbuck Fascia on exterior of door unless reverse fascia requested
	Reverse Fascia available at no charge

double dutch doors

#311CBDD2
Split Crossbuck
Double Dutch Door
Two Panels
3'11-1/2" width x
3'11-1/2" height

Recommended
Opening Measurement
4'0" width X
8'0" height

**

7' dutch door
#7CBDD2
7' Double Dutch Door
Two Panels
Top Panel
48" width x 36" height
Bottom Panel
48" width x 48" height

Recommended
Opening Measurement
4'0-1/2" width X
7'1" height

**

	Completely Assembled
	Two 4'-0" width x 4'-0" height panels *Also available in two 3'11-1/2" width x 3'11-1/2" height panels
	Twin Panels of 3/4" BC Plywood
	Bonded with glue and wood screws at back of doors.
	Wood screws installed counter sunk in critical areas for additional strength.
	All Edges surrounded with heavy gauge, "non-rusting" Mitre-Cut ALUMINUM channeling secured with wood screws.
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all doors.
	Smooth surface panels on interiors of doors.
	Crossbuck Fascia on exterior of door unless reverse fascia requested
	Reverse Fascia available at no charge
	Reversed Fascia Top Pictured
	Completely Assembled
	Two Panels: Top is 3'-0" height x 4'-0" width and Bottom is 4'-0" height x 4'-0" width
	Twin Panels of 3/4" BC Plywood
	Bonded with glue and wood screws at back of doors.
	Wood screws installed counter sunk in critical areas for additional strength.
	All Edges surrounded with heavy gauge, "non-rusting" Mitre-Cut ALUMINUM channeling secured with wood screws.
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all doors.
	Smooth surface panels on interiors of doors.
	Crossbuck Fascia on exterior of door unless reverse fascia requested
	Reverse Fascia available at no charge

#FLCBDD2
Split Flash-Panel
Crossbuck
Double-Dutch Door
Two Panels
4'0" width x
4'0" height

Recommended
Opening Measurement
4'0-1/2" width X
8'1" height

**

	Add a Little "FLASH" to Your Stall Doors
	Arrives Installed on Door or Install Yourself and Save!
	Add to an Existing Armour Dutch Door
	Completely Assembled
	Centers of door panels receive two (2) center strips of 2"x1/8" flat bar placed strategically to create the appearance of a "Split" Double Dutch Door.
	One Panel of 3/4" BC Plywood
	Bonded with glue and wood screws at back of doors.
	Wood screws installed counter sunk in critical areas for additional strength.
	All Edges surrounded with heavy gauge "non-rusting" Miter-Cut ALUMINUM channeling
	Periodic maintenance, such as painting or staining is recommended.
	All door hardware included
	Zinc-Plated Super latch and latching receiver plates
	Smooth surface panels on interiors of door
	Crossbuck Fascia on exterior of door
	Full height vertical channel materials both sides of door for maximum strength

double dutch door

#TGDD2
Tongue & Groove
Double-Dutch Door
Two Panels
4'-0" width x
4'-0" height

Recommended
Opening Measurement
4'0-1/2" width X
8'1" height

**

	Completely Assembled
	Two 4'-0" width x 4'-0" height panels
	#1 Southern Yellow Pine 6" Tongue and Groove Design
	T&G lumber is available in horizontal or vertical design
	All Edges surrounded with heavy gauge, "non-rusting" Mitre-Cut ALUMINUM channeling secured with wood screws.
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all doors.
	Smooth surface panels on interiors of doors.
	All lumber secured with glue and countersunk wood screws on rear panels.
	Reverse Fascia available at no charge

double dutch doors

#CBDDNS5
Sliding Not Split
Crossbuck
Double-Dutch Door
4'3-1/2" width x
8'-0" height

Recommended
Opening Measurement
4'0" width X
8'0" height

**

	Completely Assembled
	Centers of door panels receive two (2) center strips of 2"x1/8" flat bar placed strategically to create the appearance of a "Split" Double Dutch Door.
	One Panel of 3/4" BC Plywood
	Bonded with glue and wood screws at back of doors.
	Wood screws installed counter sunk in critical areas for additional strength.
	All Edges surrounded with heavy gauge "non-rusting" Miter-Cut ALUMINUM channeling
	Periodic maintenance, such as painting or staining is recommended.
	All door hardware included
	Zinc-Plated Super latch and latching receiver plates
	Smooth surface panels on interiors of door
	Crossbuck Fascia on exterior of door
	Full height vertical channel materials both sides of door for maximum strength

double dutch doors
(doors pictured have been painted*)

#2CBDDNS5
Sliding Not Split
Crossbuck
Double-Dutch Doors
Two 4'3-1/2" width x
8'-0" height doors

Recommended
Opening Measurement
4'0"-4'3" width X
8'0" height

**

	*DOORS ARRIVE UNPAINTED
	COMPLETELY ASSEMBLED DOORS WITH LUMBER & HARDWARE
	Custom Sizes Available, Call Us with Your Specifics
	Standard Sizes Available
	Standard Two Panels per Opening/ One Panel Option Available
	8’ Wide (Two 4’0”) Doors Overlay Your Openings, 3-1/2” on each Vertical End
	Heavy Gauge, Non-rusting Aluminum used Throughout Door Frames
	Full Height Vertical Tubing Reinforcements on Both Ends of Each Panel for Rigidity and Strength
	Full Height Astragals Available
	Smooth surface panels on "interiors" of doors (design on exterior side only)
	Counter Sunk Screw Placements (Nothing sticking out to scratch wall areas.)
	Periodic maintenance, such as painting or staining is recommended.
	Two Panels of 3/4" BC Plywood bonded with glue and wood screws at back of doors
	1-1/2” Thick Lumber Panel
	Centers of door panels receive “center strips” placed strategically to create the appearance of a "split" Double Dutch Door
	Reinforced Header Channels (Square tubing welded to upper channel inside.)
	Surrounded Lumber Fascias (Channels protect all four edges of lumber panels.)
	Full height 8'-0" Aluminum Vertical Square Tubing on Both Sides for Rigidity and Strength
	All Slider Doors Prepared for Trolley Installation Prior to Shipment at No Additional Cost
	All Necessary Hardware Included
	Galvanized, Overhead, Self-cleaning and Self-aligning Round Track
	Heavy-duty Ball-bearing Trolley System
	Heavy-duty Adjustable Wall Mount Stay-roller
	Aluminum Door Stops Included
	10” Heavy Duty Zinc Plated Door Handles
	Wood Lags Provided for Track, Stop, Handle Installation

double dutch doors

#CBDDNS2
Hinged Not Split
Crossbuck
Double Dutch Door
4'-0" width x
8'-0" height

Recommended
Opening Measurement
4'0-1/2" width X
8'1" height

**

	Completely Assembled
	Centers of door panels receive two (2) center strips of 2"x1/8" flat bar placed strategically to create the appearance of a "Split" Double Dutch Door.
	Lumber Included
	Bonded with glue and wood screws at back of doors.
	Wood screws installed counter sunk in critical areas for additional strength.
	All Edges surrounded with heavy gauge "non-rusting" Miter-Cut ALUMINUM channeling
	Periodic maintenance, such as painting or staining is recommended.
	All door hardware included
	Zinc-Plated Super latch and latching receiver plates
	Smooth surface panels on interiors of door
	Crossbuck Fascia on exterior of door
	Full height vertical channel materials both sides of door for maximum strength

double dutch doors

#CBHD1
Crossbuck Lumber
Half Dutch Gate
4'-0" width x
4'-0" height

Recommended
Opening Measurement
4'0-1/2" width

**

	Completely Assembled Stall Gate with Hardware
	Old World Crossbuck "x" Design
	One 4'-0" width x 4'-0" height panel *Also available in one 3'11-1/2" width x 3'11-1/2" height panel
	Heavy gauge "non-rusting" ALUMINUM metal used throughout entire gate structure (except lumber)
	Full vertical & horizontal channel coverage on both sides of door for maximum strength and protection
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all gates.
	Smooth surface inside door panel.
	All lumber secured with glue and countersunk wood screws on rear panels.
	Check out the Double-Dutch Door

double dutch doors

#311CBHD1
Crossbuck Lumber
Half Dutch Gate
3'11-1/2" width x
3'11-1/2" height

Recommended
Opening Measurement
4'0" width

**

	Completely Assembled Stall Gate with Hardware
	Old World Crossbuck "x" Design
	One 4'-0" width x 4'-0" height panel *Also available in one 3'11-1/2" width x 3'11-1/2" height panel
	Heavy gauge "non-rusting" ALUMINUM metal used throughout entire gate structure (except lumber)
	Full vertical & horizontal channel coverage on both sides of door for maximum strength and protection
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all gates.
	Smooth surface inside door panel.
	All lumber secured with glue and countersunk wood screws on rear panels.
	Check out the Double-Dutch Door

half dutch doors

#FLCBHD1
Flash-Panel
Crossbuck Lumber
Half Dutch Gate
4'-0" width x
4'-0" height

Recommended
Opening Measurement
4'0-1/2" width

**

	Add a Little "FLASH" to Your Stall Doors
	Arrives Installed on Door or Install Yourself and Save!
	Add to an Existing Armour Dutch Door
	Completely Assembled Stall Gate with Hardware
	Old World Crossbuck "x" Design
	One 4'-0" width x 4'-0" height panel
	Heavy gauge "non-rusting" ALUMINUM metal used throughout entire gate structure (except lumber)
	Full vertical & horizontal channel coverage on both sides of door for maximum strength and protection
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all gates.
	Smooth surface inside door panel.
	All lumber secured with glue and countersunk wood screws on rear panels.

#TGHD1
6" T&G Lumber
Half Dutch Gate
4'-0" width x
4'-0" height

Recommended
Opening Measurement
4'0-1/2" width

**

	Completely Assembled Stall Gate with Hardware
	#1 Southern Yellow Pine 6" Tongue and Groove Design
	One 4'-0" width x 4'-0" height panel *Also available in one 3'11-1/2" width x 3'11-1/2" height panel
	T&G lumber is available in horizontal or vertical design
	Heavy gauge "non-rusting" ALUMINUM metal used throughout entire gate structure (except lumber)
	Full vertical & horizontal channel coverage on both sides of door for maximum strength and protection
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all gates.
	Smooth surface inside door panel.
	All lumber secured with glue and countersunk wood screws on rear panels.
	Check out the Double-Dutch Door

#311TGHD1
6" T&G Lumber
Half Dutch Gate
3'11-1/2" width x
3'11-1/2" height

Recommended
Opening Measurement
4'0" width

**

	Completely Assembled Stall Gate with Hardware
	#1 Southern Yellow Pine 6" Tongue and Groove Design
	One 4'-0" width x 4'-0" height panel *Also available in one 3'11-1/2" width x 3'11-1/2" height panel
	T&G lumber is available in horizontal or vertical design
	Heavy gauge "non-rusting" ALUMINUM metal used throughout entire gate structure (except lumber)
	Full vertical & horizontal channel coverage on both sides of door for maximum strength and protection
	Periodic maintenance, such as painting or staining is recommended.
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all gates.
	Smooth surface inside door panel.
	All lumber secured with glue and countersunk wood screws on rear panels.
	Check out the Double-Dutch Door

#BTHD1
Bar Top
Half Dutch Gate
4'-0" width x
4'-0" height

Recommended
Opening Measurement
4'0-1/2" width

**

	Completely Assembled Stall Gate with Hardware
	Full Height 1-3/4" x 1-3/4" x 1/8" Square Tubing Posts.
	One 4'-0" width x 4'-0" height panel *Also available in one 4'0" width x 3'0" height panel
	1" Diameter Round Vertical Pickets (Bars)
	Heavy gauge "non-rusting" ALUMINUM metal used throughout entire gate structure
	Full vertical & horizontal channel coverage on both sides of door for maximum strength and protection
	3” Between Picket (Bar) Spacing (1" & 2" also available)
	6" Zinc Plated Tee-Hinges with all necessary fasteners included for installation.
	Zinc-Plated Superlatch and latching receiver plates and hardware included with all gates.
	Smaller Custom Sizes are Available (Nothing Exceeding 48" Width x 48" Height)

Please Note: When ordering Double-Dutch Door's with Reverse Fascia you have the option of having the "x" or the T&G pattern shown when the top is open and the bottom is closed. We offer this option at no charge upon request.

** Please note that items purchased will be through our affiliate website www.aluminumhorsestalls.com
and you will be advised of applicable shipping charges pertaining to specific orders after
quantity and destination are determined by a member of our sales team.